Replacing uPVC Window Handles
It is simple to change the handles on windows made of Upvc. It is essential to make sure that the new handle fits inside the spindle cutout in the window mechanism.
If the steps below are followed properly If you follow the steps correctly, any cockspur handle can fit most windows. upvc door handle www.repairmywindowsanddoors.co.uk is the step height of the handle.
What to Look For
Many of the windows in the UK come with uPVC handles, and over time they can begin to show signs of wear and wear and tear. The handle of the window can become loose or difficult-to-operate when this happens. Anyone who is proficient with basic hand tools can accomplish this fairly simple job.
The first step is to make sure that the handle is securely connected to the window frame and is in the open position. The next step is to locate the pins or screws that secure the handle in place. These are usually located on the inside of the handle. They can be removed with a screwdriver and pliers.
Once the handle has become loose, gently pull it away from its hinges. Then, you will need to locate a new handle of the same dimensions and style. This can be done on the internet or in a local DIY store, and should take around five minutes using an screwdriver.
One important factor to consider when replacing a uPVC window handle is the step height. This is the distance from the bottom of the handle until it rests on the window frame. This is a common measurement and you should confirm the height of the step prior to ordering a replacement handle.
There are several sizes depending on the type of handle. Inline handles can be found for uPVC window with centers of 31mm for lugs, while cockspur handles have lug centres of 43 millimetres. Tilt-and-turn handles are commonly found on uPVC Windows. They have a special design that allows the window to be tilted for ventilation, and then turned to fully open the window.
The most frequent breakage in uPVC handles is that they crack inside rather than breaking off from the base section. This makes it difficult to open. It is essential to ensure that the replacement handle is fitted with the same spindle that was used in your original one.
Remove the old Handle
If the handles on your windows are damaged or incorrectly fitted, they can cause double-glazed windows to not open or close correctly. They may even get stuck. There are many reasons for this, such as general wear and tear or the corrosion of the metal handle. In these situations, it is important to locate replacement window handles made of upvc as soon as you can to avoid further damage and loss of function.
One of the first things that you should do when replacing upvc window handles is to remove the old handle from the window. To do this, begin by taking off the screw that is covered when the handle is in its closed position. This should reveal another screw and once removed, you can begin to remove the handle. It is recommended to employ an electric screwdriver to accomplish this since it will make the task much easier and quicker.
It is also worth noting that the screws on the handle could be hidden behind plastic caps, so it is recommended to use a Stanley knife to the screw caps and then take them off. After removing the handle, you'll need to check the square cutout on the base to ensure that the new handle you choose for the window lock is compatible. It is important to measure the spindle length on the handle you used to replace it with and then compare it with the dimensions of the window mechanism spindle cutout.
There are three kinds of upvc handles: Espag handles with a central screw that can be turned right or left and Cranked handles that have two screws and Spade handles, which are made of flat arms and can be used either side of the window made of upvc. When you have a suitable replacement, it is just a matter of screwing the handle in place and making sure that the spindle is placed into the lock mechanism. Once you have done this then tighten the handle to the window frame. The replacement upvc handle should now be secure.
Take a measurement of the Spindle
If you're replacing a Upvc window handle that has fallen off, it's due to the spindle that holds it in place has become damaged or loose. In some instances, you can tighten the spindle using a screw or pin. In other situations, it will require replacement completely. There are many kinds of window handles made of upvc. There are three kinds of handles: inline espagnolette tilt-and-turn, and cockspur. Each kind has a distinct method for installing and replacing the handle.
It is essential to measure the handle prior to purchasing an alternative. This will ensure that the handle will fit the window properly and will be the right size. Luckily, all handles conform to industry standards of sizing making it quite easy to locate the correct size.
To determine the size of the handle you must turn the window to the open position. You should then be able to determine the size of the screw or pin that holds it. Make use of a ruler or tape measure to determine how long the spindle is. Once you have the length of your spindle it is possible to purchase a replacement of the exact same length.
The step height of a window handle is also a factor to take into consideration when buying replacements. The step height is measured from the base to the point where the handle is positioned on the frame. Typically, this is about 21mm for uPVC windows and 9mm for aluminium. Dropping objects into the gap will let you determine how far the handle extends before it comes into contact with an obstruction.
Cockspur handles usually have different backset heights based on the style of window they are placed in. Inline Espag handle heights are 43mm from centre to center (two fixing points). Cockspur handles have different backsets depending on which window design they are placed in. This is because they have an extension spur that extends from the handle and locks over a cockspur wedge striker.
Fit the New Handle
Once you've selected the new handle, ensure that it is aligned with the screw holes on the door. Then, secure it with the screws supplied. Install the latch lever the same manner as the main handle in the event that you are replacing the door handle. After that, attach the door trim to conceal the mounting screws and finish off your project.
Tip: To remove a metal head from a wooden wedge, place the handle on the floor so that its wide end is on the floor. Then, use a hammer and tap the thin end. Be careful not to damage the handle or the spindle.